.dfx file gps pathfinder office generator#
.dfx file gps pathfinder office license#

If you are going to be off the network, then you must borrow a license from the Polyworks license server to be able to use the software. _ Laptop with Polyworks installed (with REQUIRED Plugins Add-on). _ Turntable вЂ“ optional (Medium black hard case) _ VIVID 9i Scanner (Large orange hard case)

.dfx file gps pathfinder office generator#

The Minolta is also meant to be plugged in, so a generator or alternate power source is required when working outdoors. Any planned outdoor scanning should be done at night or under a blackout tent. It will not work in direct or indirect sunlight. Note: The Konica Minolta VIVID 9i is best suited for indoor use. If the camera indicates Good, take a test image to visually check your white balance The camera should indicate вЂњGoodвЂќ or вЂњNo GdвЂќ вЂ“ if вЂњNo GdвЂќ try againДҐ. Use the shutter release button to capture a photograph of healthy green grass in similar lighting as your intended subject (e.g. Hold down the вЂњWBвЂќ button until вЂњPREвЂќ begins to flashДЈ. Hold down the вЂњWBвЂќ button and rotate the rear wheel to select the вЂњPREвЂќ setting, release WBДў. To use the White Balance Preset option, follow these instructions to capture an appropriate custom WB image:ДЎ. However, even when capturing RAW images, the image preview on the cameraвЂ™s LCD will use the white balance setting, and will therefore be easier to evaluate exposure in the field. ItвЂ™s important to note that the white balance setting is only applied to JPEG images saved on the memory card вЂ“ RAW images are saved to the memory card exactly as they are recorded by the image sensor, without any processing. A custom white balance using the вЂњWhite Balance PresetвЂќ option can be used for better images. Nikon D200IR Custom White Balance ResultsД«ecause some red light is transmitted by the IR filter, any of the standard white balance settings will produce reddish images. This would result in 100 total images, with two at each of the 50 positions (interval) If mounting the camera to the octocopter for example, one could set the Interval to 10 seconds, the total number of intervals to 50, and the number of images at each interval to two. Select Intvl*Shots: This setting ask you to set 1. Interval: Sets the amount of time between each interval using hours, minutes, and/or seconds (one second minimum)ДЈ.

If using Start Time, make sure the cameras time setting is correctДў. Start: Two options exist including вЂњNowвЂќ (starts taking images right away) or вЂњStart TimeвЂќ (allows you to set a time (e.g. To use this setting, three setting must be set:ДЎ. вЂ“ Intvl Timer Shooting: This setting can be used to take a predetermined number of images with a certain amount of time between each shot. Otherwise turning on compression will cut the size of RAW images from 16MB to 9MB вЂ“ RAW Compression: If memory card space is not an issue, set to вЂњNEF (RAW)вЂќ for no compression. вЂ“ JPEG Compression: For highest quality set to вЂњOptimal QualityвЂќ

вЂ“Make sure you select вЂњDoneвЂќ after making adjustments to theses settings or they will be lost. вЂ“ Optimize Image: Use these вЂњCustomвЂќ settings and adjust as needed: Capturing RAW images will preserve all image information and give you much more control over editing later вЂ“ Image Quality: Use either the вЂњNEF (RAW)вЂќ or вЂњNEF (RAW)+JPEGвЂќ image quality setting. вЂ“ Rotate Tall: Set вЂњRotate TallвЂќ to Off if the images are to be used for photogrammetry or GIS applications Along with the generic advise given in the Acquire Images for Close-Range PhotogrammetryВ and Custom White Balance for Nikon D200 IR posts, here are some important settings to consider when using the standard or IR modified Nikon D200 cameras: